Weed gone to seed because left out to long

I have an indoor growroom and in my recent harvest I found seeds in the buds, but I’m sure there are no male plants in the room. I’ve heard that light leakage can cause plants to become hermaphrodites. Is this true, and if so, do you have any tips for avoiding this?

Cannabis plants are monecious. This means they have the ability to be either male or female. Or in the case of hermaphroditism, they can be both. The reason to make sure there are no males or hermaphrodites in your garden is because male flowers make pollen. When pollen touches the white hairs on a flower, it makes a seed, and seeded weed gives you headaches. Even though there are reasons in nature hermaphroditism could be important, such as continuing the species in case there is no male present, hermaphroditism is generally a bad thing when talking about cannabis plants.

Light poisoning is the most common cause for a normal plant to hermaphrodite.

Light poisoning refers to the flowering night cycle of a plant being unnaturally interrupted with light. The best way to prevent this is to close yourself inside your darkened room during the daylight, and then after allowing a few minutes for your eyes to adjust to the dark, check for any light leaks from covered windows, door jams, etc. Also cover all timer and appliance lights with tape.

Negative stressors can combine with small interruptions of the light cycle to cause hermaphroditism, especially with less-stable, clone-only hybridized strains. When the night cycle is abnormally interrupted, it sends a mixed hormonal signal to the plant. This can cause a full female plant to throw some male flowers. Male flowers are easy to identify, especially when side by side with female flowers. Male flowers look like small bunches of bananas, which will take a week or two to swell before they burst and release their pollen.

Read also:

Finding a hermaphrodite in your growroom can happen at any stage of the flowering cycle and is indicated by the presence of male flowers growing on the same plant as female flowers. As with all species in nature this can occur in varying degrees. A plant can become slightly or majorly hermaphroditic. In cases where singular male flowers are found between the branch and stalk nodes, you should be diligently removing them as they grow. You must re-inspect the plant top to bottom every few days to be sure pollination and seeding doesn’t occur. If you find male flowers (anthers) actually growing from within the female flowers (buds) the situation is a little more dire. You can still remove all the male anatomy as it appears, but it will be harder to find and much more prevalent. This is a horrible discovery that leads to a tough decision: Should you let the plant live and risk the whole crop being ruined by seeds?

In either case, once hermaphroditism has compromised the safety and purity of your sensimilla, the plant should not be propagated further. Remember, once a hermy, always a hermy. The plant pictured here is in the tenth and what should have been the final week of ripening, but a timer failed and one light stayed on continuously for almost two weeks, causing this vegetative regrowth. Because the light was continuous, the plant made no pollen. This method of re-vegging can be used to save a flowering plant you have no copies of, but be careful, as this may cause some strains to hermaphrodite.

Purposefully causing a plant to hermaphrodite is called selfing. Gibberellic acid or colloidal silver is typically sprayed onto the female plant. This technique is used to make feminized seeds and uses the plant’s ability to be both male and female to force a female plant to produce male flowers. The pollen contained in these male flowers can only produce female seeds. Just keep in mind that feminized plants should not be used for breeding, as they were produced without a true male, making them genetically inferior.

The Stages of Cannabis Growth

Cannabis growth is made up of a series of stages that plants undergo during their lifecycle. Each stage during the cannabis cultivation process requires its own unique demands, including different levels of light, water, and nutrients.

It can take anywhere from 4 to 8 months to grow a cannabis plant, this varies based on where you’re growing. If you have an indoor grow room, your plant has the ability to flower after only a few weeks!

The quality of your plant depends on your knowledge of the cannabis growth stages and the lifecycle of your plants.

Cannabis Growth Timeline

1. Germinating: 1-7 days
2. Seedling: 2-3 weeks
3. Vegetative: 2-8 weeks
4. Pre-Flowering: 1-2 weeks
5. Flowering: 6-8 weeks
6. Harvesting

1. Germinating Seeds

2. Seedling Stage

3. Vegetative Growth

4. Pre-flowering

How to tell if your plant is a male or female

Female: Two pistils (the pistil contains the reproductive parts of a flower) will be growing on the buds (flowers grow above these leaves, one cluster on each side).

Male: Small green sacs full of pollen will be seen on the node areas.

5. Flowering

  • If there is a high color ratio of white to red pistils your cannabis will provide a euphoric THC high.
  • If the color ratio is more red to white, your cannabis will provide a calmer, CBD-stoned feeling.
  • If you harvest once half the trichomes are opaque and the pistils haven’t turned brown, your cannabis will provide a balanced THC/CBD high.

6. Harvesting

Covid-19 Plan
We Are Open, Essential, and Shipping On Time!

As a manufacturer and distributor of Air Cleaning, Ducting, and Filtration products we are proud to have been identified as an essential business. We will remain open for business performing essential operations during this crisis, supplying industrial, military, and healthcare operations with our products. We are shipping orders on time, with no delay in manufacturing.

Our phone lines are open from 9am-5pm central time, Monday through Friday. Our staff is working remotely wherever possible and we will maintain a bare minimum staff on-site to perform basic operations of order processing and accounting. Our on-site staff will follow the appropriate best practices and guidelines set forth by OSHA’s latest release of “Guidance on Preparing Workplaces for COVID-19.”

These are unprecedented times and we are committed to protecting both our employees and our communities. Clean air has never been more important, and we’re making sure our customers have everything they need. From those working from home who need high quality air filters, to the other essential businesses we supply products to, we’re here for you.

We thank you for your support and your business and we hope that this will all be over soon.